Results for 'Polymer Li Ion Battery 3 6V'

Cautions

• Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode if mis-handled.
  
• Make sure user has enough knowledge on Li-Ion rechargeable batteries in charging, discharging and assembly before use.
  
• We are not responsible for any damage caused by misuse or mishandling of these Polymer Li-Ion batteries
  

Specifications:

Easy Connection:

Li-Ion and Li-polymer Battery packs must have a protection circuit module to keep Li-Ion/Polymer Battery from over charge, over discharge and prevent accidental battery explosion due to its extra high energy density. This protection circuit board is specially designed for 18.5v Li-Ion Battery packs made of Li-ion and Li-Polymer cells.

• Keep 18.5V Li-Ion Battery packs from overcharge and over discharge
• Limit the Max discharge Current to 8.0 A.
• Designed for 5 Cells?€?Li-ion /Li-polymer Battery Packs
• Li-ion/Polymer Battery Protection
• SEIKO S8233 Protection IC
• IR IRF4906, FDS9926 MOSFET
• Dimension: 3.55" x 0.8"inch

PCB Indications

• B+ Battery (+)
• B- Battery (-)
• P+ OUT (+) /Load (+)
• C+ OUT (+) /Charge (+)
• P- OUT (-) /Charge(-) / Load(-)

Electric performance

• Overcharge Protection voltage for single cell:4.235V +/- 0.025V
• Over discharge Protection voltage for single cell:2.30V+/-0.08V
• Over current detection Protection:<=8 A +/-1A
• Supply current:MAX 600uA
• Short circuit Protection
• 0 V charge
• Protection circuit Resistance: <=10 mill-oHms

Specifications:

Easy Connection:

Li-Ion and Li-polymer Battery packs must have a protection circuit module to keep Li-Ion/Polymer Battery packs from over charge, over discharge and accidental battery explosion due to its extra high energy density. This Protection Circuit Board is specially designed for 29.6V 8 Cells Li-Ion Battery packs made of Li-ion and Li-Polymer cells.

• Keep 29.6V Li-Ion Battery pack from overcharge and over discharge
• Keep 29.6V Li-Ion Battery pack 's discharging current lower than 10 A
• Short Cut Protection
• 8 Cells Li-ion / Li-polymer Battery Pack ( 29.6V up to 20 Ah)
• Battery Protection
• Dimension: 2.87" x 1.69 " inch

PCB Indications

• B+ Battery (+)
• B- Battery (-)
• P+ OUT (+) /Load (+)
• C+ OUT (+) /Charge (+)
• P- OUT (-) /Charge(-) / Load(-)

Electric performance

• Overcharge Protection voltage for single cell: 4.235V +/- 0.025V
• Overdischarge Protection voltage for single cell: 2.30V +/-0.08V
• Overcurrent detection Protection <= 10 A +/-1A
• Supply current: MAX 600uA
• Short circuit Protection
• 0 V charge
• Protection circuitry Resistance: <= 10 mohms

Specifications:

Easy Connection:

Li-Ion and Li-polymer Battery packs must have a protection circuit module to keep Li-Ion/Polymer Battery packs from over charge, over discharge and accidental battery explosion due to its extra high energy density. This Protection Circuit Board is specially designed for 37 V Li-Ion Battery packs made of Li-ion and Li-Polymer cells.

• Keep 37V Li-Ion Battery pack from overcharge and over discharge
• Keep 37V Li-Ion Battery pack 's discharging current lower than 27 A
• Short Cut Protection
• 10 Cells Li-ion / Li-polymer Battery Pack ( 37V up to 27 Ah)
• Battery Protection
• Dimension: "2.4" x 3.25" inch

PCB Indications

• B+ Battery (+)
• B- Battery (-)
• P+ OUT (+) /Load (+)
• C+ OUT (+) /Charge (+)
• P- OUT (-) /Charge(-) / Load(-)

Electric performance

• Overcharge Protection voltage for single cell: 4.235V +/- 0.025V
• Over discharge Protection voltage for single cell: 2.30V +/-0.08V
• Over current detection Protection <= 27A~33A
• Supply current: MAX 300uA
• Short circuit Protection
• 0 V charge Protection
• Circuit Board Resistance: <= 6.67 milliOhms

Prismatic Polymer Li-Ion Battery, 3.7V, 875mAh (383562) for RC Car and RC Plane or Micro Device

Cautions

• Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode if mis-handled.
  
• Make sure user has enough knowledge on Li-Ion rechargeable batteries in charging, discharging and assembly before use.
  
• We are not responsible for any damage caused by misuse or mishandling of these Li-Ion batteries
  

Prismatic Polymer Li-Ion Battery, 3.7V, 430mAh for RC Car and RC Plane or Micro Device

Cautions

• Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode if mis-handled.
  
• Make sure user has enough knowledge on Li-Ion rechargeable batteries in charging, discharging and assembly before use.
  
• We are not responsible for any damage caused by misuse or mishandling of these Li-Ion batteries
  

Cautions

• Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode if mis-handled.
  
• Make sure user has enough knowledge on Li-Ion rechargeable batteries in charging, discharging and assembly before use.
  
• We are not responsible for any damage caused by misuse or mishandling of these Li-Ion batteries
  

Prismatic Polymer Li-Ion Battery, 3.7V, 2700mAh for Lighting and Laptop

Cautions

• Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode if mis-handled.
  
• Make sure user has enough knowledge on Li-Ion rechargeable batteries in charging, discharging and assembly before use.
  
• We are not responsible for any damage caused by misuse or mishandling of these Li-Ion batteries
  

Specifications:

Easy Connection:

Li-Ion and Li-polymer Battery packs must have a protection circuit module to keep Li-Ion/Polymer Battery from over charge, over discharge and prevent accidental battery explosion due to its extra high energy density. This protection circuit is specially designed for 22.2V Li-Ion Battery packs made of Li-ion and Li-Polymer cells.

• Keep 22.2V Li-Ion Batery pack from overcharge and overdischarge
• Limite the Max Cuurent to 8.0 A.
• Designed for 6 Cells Li-ion /Li-polymer Battery Packs
• Battery Protection
• Adopt SEIKO S8233 Protection IC
• Adopt IR IRF4906, FDS9926 MOSFET
• Dimension: 2.6" x 1.7" inch

PCB Indications

• B+ Battery (+)
• B- Battery (-)
• P+ OUT (+) /Load (+)
• C+ OUT (+) /Charge (+)
• P- OUT (-) /Charge(-) / Load(-)

Electric performance

• Overcharge Protection voltage for single cell: 4.235V+/-0.025V
• Over discharge Protection voltage for single cell: 2.30V+/-0.08V
• Over current detection Protection <=8A+/- 1A
• Supply current: MAX 600uA
• Short circuit Protection
• 0 V charge
• Protection circuitry Resistance: <= 10 milli-ohms

• Intelligent charger designed for all types of 14.4V (4 cells) Li-Ion Battery packs including Polymer Li-Ion and Cylindral Li-Ion.
• Worldwide input AC power from 110V --- 240V.
• 1500 mA (1.5A ) constant charging current for faster charging, save your much more time.
• Charging time for 4000mAh battery pack is about 2.6 Hrs. ( Please use it to charge Li-Ion battery with capacity > 1500mAh)
• Built in IC to cut off power automatically when battery is fully charge.
• Red Lead will show Battery in charging and Green LED shows full. (LED also is full without battery).
• Two pins male connector is for connecting to Li-Ion battery pack
• One 5' cable with male connector is included , which allow you connect it to a battery pack and fits with the smart charger.
• Dimension: 2.5" L x 1.25" W x 1" H.
• Compact size and lightweight. It is perfect to charger our 14.4V Li-Ion battery pack module and 14.4V Li-Ion battery pack for bike-lighting

Warning:

• Only charge Li-Ion battery pack with capacity more than 1500 mAh. Don't use the charger for lower capacity Li-Ion battery pack.
• Only charge Li-Ion battery pack with voltage 14.8V ( 4 cell pack ) . Don't use the charger for Lower voltage battery pack, whcih may cayse battery exploded
• We are not responsible for any damage baused by user and miss use.

Features and Benefits

• Protection Circuit Board for 11.1V Li-ion and Li-polymer battery pack
  
• Designed for 11.1V Li-ion or Li-Polymer battery
  
• Prevent 11.1V Li-ion or Li-polymer battery from over-charging, over-discharging and from discharging current more than 5A.
  
  

Connection Instruction

Port # Connection
B+ To battery (+)
B- To battery (-)
P- Output (+) r Charger (+)
P+ Output (+) r Charger (+)
B1- To battery 2 (+) and battery 3 (-)
B2- To battery 1 (+) and battery 2 (-)